1、濟南防水公司http://www.tianyujian.com/談到對于鋁合金窗戶做防水防漏作業時，要清除鋁合金和玻璃、鋁合金和鋁合金材料之間的已經老化了的密封材料?？紤]到鋁合金窗的結構一般為凹進結構的，因此，為防止雨季下雨后發生雨水的毛細現象，窗戶頂部要做滴水鷹嘴。
When it comes to waterproofing company Jinan Aluminium windows do water leak, clear the aging of the sealing material of aluminum and glass, aluminum and aluminum alloy materials. Taking into account the aluminum window structure is generally recessed structure, therefore, occurred after the rainy season in order to prevent rain rain capillarity, the top of the window do drip beak.
2、濟南防水公司介紹玻璃于鋁合金粘接處不要使用膠條進行粘接，會粘不住，一定要使用密封膠，要將密封膠注入到玻璃和鋁合金框連接處才能穩妥的粘黏在一起，而且不會發生雨水從此處滲漏至屋內的現象。
Jinan waterproofing company presentation at the bonding glass to aluminum bonding strips do not use, it will not stick, be sure to use sealant to sealant injected into the glass and aluminum frame to secure the connection with sticky and rainwater leaking from here to the house does not occur.
3、濟南防水公司介紹窗戶框周邊與其他材料的交界處同樣要使用密封膠進行粘接，并且要使用防水密封膠。窗戶防水，雖說如果外墻滲水，屋內做防水基本上作用不大，所以，窗戶的防水防漏要先從外墻做起，在外窗框的周邊要刷涂防水材料，比如說丙烯酸類、JS類等。
Jinan waterproofing company introduced around the window frames and other materials at the junction of the same adhesive sealant to be used, and to use a waterproof sealant. Windows waterproof, although if the external walls of water seepage, the house is basically a waterproof little effect, so the windows from the outside wall of water leak first start, you want to brush around the outer sash waterproof material, such as acrylic, JS and so on.
4、濟南防水公司http://www.tianyujian.com/建議在鋁合金材拉床軌道處多打幾個排水槽，這樣能防止雨季來臨時雨水不會存積在窗戶槽內排不出去，多打幾個排水槽讓雨水能及時順利的從軌道內排出。窗戶底部與窗臺的交接處，窗臺板要設計成朝外的并且要有一定的坡度，方便雨水向下流而不會流入室內。窗臺板與窗戶的膠縫要設計成朝外的，不能設計成朝上的。
Jinan waterproof aluminum timber company recommends broaching track at more than a few drainage channels, which can prevent the rainy season is not accumulated rainwater tank in the window did not break out, more than a few drainage channels so that rainwater can promptly smoothly discharged from the inner rail. The bottom of the window and sill junction, sill plate and should be designed to have a certain outward slope, rainwater flows down rather easily flow into the room. Sill plates and windows should be designed to glue seam outward, not designed to be upward.